Painted Canvas Signs

These signs were so easy to make and cheap. I used my Silhouette Cameo to make the vinyl template, and laid it down the canvas. I didn't not use transfer paper, because I was going to "pop" the letters out anyways. After popping the letters out, I just painted and it let dry. Once it had dried I peeled the template off. So simple.

Now, if you don't have a Silhouette, you can always paint your canvas and lay down vinyl store bought letters. After laying down your vinyl letters you will need to just paint over the whole canvas in a different color. Let the paint dry, and peel off your vinyl letters. :)

Happy Crafting. :) 

Pumpkin Patch

How cute are these pumpkin shirts? I just love them. What I love more is that the appliqué was FREE. I was going to link the site, but when I wen to link it in the post I couldn't find it any more. :/ 

Boo For You Halloween Wreath

Halloween Wreath

I love deco mesh wreaths. We live in the country and no can see the wreaths, so I just have them hanging on the inside of my door. ;) Plus it keeps the bugs out of them too. Funny story, I helped my sister-in-law make a pumpkin wreath, and when she opened the door two House Wrens flew into the house. They were nesting in the wreath. Wish I could have seen my brother trying to catch those birds. 

Materials: 

21" Halloween deco mesh (I just used one, but probably should have used 1.5-2 rolls)

2 (or more) color of 5.5" deco mesh to coordinate with the 21"

wire wreath 

black pipe cleaners

I looped the 21" deco mesh around the outside ring of the wired wreath with black pipe cleaners. I did cut the pipe cleaners in fourths for this part. 

After the outside loop I then skipped a wire, and looped the mesh around the 3rd wire.  (if I did it again, I would probably alternate it back and forth from the outside loop to the 3rd loop).

Next, I cut about 6-8 inches of the green and orange deco mesh, and just twisted it in the direction it naturally curls. Alternate the colors and pinch from the bottom. Once I folded the curly-cues up, they were bond with a pipe cleaner that was cut in half. 

I did two curly-cues of each color per bunch. 

You can add any decoration you would like. :)

Happy Crafting. 

Hair Bow Holder

After I learned to make hair bows, I went on a bow making frenzy and before I knew it Catherine had so many bows laying around everywhere. Unfortunately, there is not a craft store in my little town so I headed on over to Wal-Mart to check out the craft aisle. I picked up a wood plaque pictured below and decided it would do. Happy Crafting...

Materials:

wood plaque

paint color of your choice

ribbon

hot glue gun

vinyl letters

drill 

thumb tack/ or nail

I used some left over paint that I had laying around the house to paint the plaque. There is actually an edge on this plaque that I painted white, and rest is painted pink (Catherine's favorite color at this stage).   Next, you will need to cut your ribbon to the length you prefer, with the end ribbons the same length and the middle ribbon a tad bit longer. Hot glue the ribbon with equal distance between to the back of the plaque. I then had my husband drill a hole in the top center of the plaque, so I could hang it on the wall (just make sure you don't go through the plaque. I used my Silhouette Cameo to make the vinyl letters for Catherine's initials. You can buy vinyl letters at Wal-Mart or any craft store as well. I also used a thumb tack to hang the hair bow holder with, because I don't like big holes in the wall.  

  

Happy Fall Y'all!

I have been wanting to make a pumpkin deco mesh wreath for some time now, and I finally got around to it. It was very easy to make too, and I am loving the way it turned out. Hope you enjoy :)

Materials Used: 

1 Medium wire wreath hoop

14 Orange Pipe Cleaners

1 roll of 21"Orange Deco Mesh

small roll of black deco mesh

wired ribbon of any color

hot glue gun

I did paint the hoop (partially).  I then tied 7 pipe cleaners on top and 7 pipe cleaners on bottom. Once they were place, I hot glued the pipe cleaners to ensure they wouldn't slide around. 

I left about 8" of mesh for a tail, and gathered the mesh by just pinching it. 

Next, place the deco mesh into the pipe cleaners and twist it off. You will want to leave enough room to make the pumpkin poofy. 

Just weave the mesh back and forth until you cover the entire length of the wreath.

I then used wire ribbon to make a bow, and black deco mesh for the pumpkin steam.